19 11 月, 2025 • 6 min read
From 2 Operators to 1: Robotic Bending Automation for Sheet Metal Panels

Robotic bending automation offers manufacturers a practical way to reduce repetitive manual handling while maintaining consistent production of sheet metal components.
For large panels requiring multiple bends, material positioning and workpiece transfer can consume considerable labor time.
This KLD application examines how an automated robotic bending cell was configured to process 1,200 mm square perforated panels while reducing the number of operators directly involved in the bending process.
The Customer's Challenge: Repetitive Manual Bending
The customer manufactured square perforated sheet metal panels requiring bending along all four sides.
Each panel measured approximately 1,200 mm × 1,200 mm.
Before automation, the process required two operators to transfer the material, position the workpiece, complete the bending operations, and move finished parts to the collection area.
Repeated handling created several production challenges:
- Significant manual positioning and transfer work
- Dependence on two operators during bending
- Repetitive lifting and repositioning
- Limited productivity during continuous production
- Difficulty increasing output without additional labor
The customer needed a solution that could reduce manual intervention while maintaining reliable bending operations.
The KLD Robotic Bending Solution
The proposed automated bending cell integrates a CNC press brake, industrial robot, positioning equipment, and material handling mechanisms.
The system is designed to coordinate several operations within one production cycle.
Main System Components
CNC Press Brake: Performs the programmed bending operations using the selected tooling and machine settings.
Industrial Robot: Transfers and manipulates the sheet metal workpiece during the automated bending sequence.
Automatic Loading Mechanism: Supplies workpieces to the production cell.
Gravity Positioning Table: Supports repeatable workpiece alignment before subsequent operations.
Positioning Detection System: Helps verify workpiece position during automated handling.
Customized Gripper: Provides workpiece handling suited to the panel geometry.
Safety Enclosure: Separates automated robot movement from personnel during operation.
Together, these components reduce the need for operators to reposition each panel manually.
How the Automated Process Works
The robotic bending cycle follows a coordinated sequence.
First, the loading mechanism presents the sheet metal blank to the robot.
The robot picks up the workpiece using its configured gripper and transfers it to the positioning station.
After alignment, the robot presents the panel to the press brake for the first bending operation.
The workpiece is then repositioned as required to complete the remaining bends.
Once the bending sequence is finished, the robot transfers the completed panel to the designated unloading area.
The exact movement sequence depends on the programmed component geometry and system configuration.
Production Efficiency Comparison
The supplied project data provides a useful comparison between manual and automated bending.
| Performance Indicator | Manual Process | Automated Process |
|---|---|---|
| Operators assigned | 2 | 1 |
| Average cycle time | Approximately 125.6 seconds | Approximately 66 seconds after initial cycle |
| First automated cycle | — | 100 seconds |
| Repetitive handling | Manual | Robot-assisted |
| Production supervision | Operator-dependent | One operator supervising and handling materials |
The manual average is calculated from ten recorded cycles. The automated process recorded a 100-second initial cycle followed by 66-second cycles in the supplied sample.
Based on the stabilized cycle times, the bending cycle is approximately 47% shorter.
Theoretical throughput at 66 seconds per part is approximately 54.5 parts per hour, compared with approximately 28.7 parts per hour at the manual sample average.
These figures represent the supplied cycle-time comparison, not independently verified long-term production performance.
Why Reducing Operator Requirements Matters
Reducing the process from two operators to one can improve labor allocation.
The remaining operator can focus on supplying raw material, collecting finished parts, monitoring production, and responding to process alarms.
However, operator reduction does not automatically translate into equivalent financial savings.
Actual savings depend on labor allocation, shift patterns, equipment utilization, and production demand.
Where Can This Solution Be Applied?
Robotic bending automation is particularly relevant for repetitive sheet metal components such as:
- Electrical cabinet panels
- Industrial equipment covers
- HVAC equipment enclosures
- Metal furniture components
- Machinery protection panels
- Repetitive four-side bent components
Compatibility must be verified against material thickness, panel dimensions, bend geometry, and gripper requirements.
Key Takeaways
This application demonstrates how automated loading, robotic handling, positioning, and CNC bending can be coordinated to reduce repetitive manual work.
The main value lies in combining equipment functions into a repeatable process rather than automating only the press brake stroke.
For manufacturers evaluating similar applications, KLD Machinery can assess representative workpiece drawings, production volumes, and handling requirements to determine a suitable robotic bending configuration.
Frequently Asked Questions
Can robotic bending automation reduce the number of operators?
Yes, for suitable applications. This case compares a two-operator manual process with a one-operator automated workflow.
Can one robotic bending cell perform four-side bending?
Yes, when the part geometry, gripper, positioning equipment, and bending sequence are compatible.
Does automation guarantee the same cycle time for every part?
No. Cycle time depends on material, geometry, number of bends, robot movement, and handling requirements.
What information is needed to evaluate robotic bending?
Manufacturers should provide part drawings, material specifications, dimensions, production volumes, and current cycle times.
Conclusion
Robotic bending automation can reduce repetitive material handling and improve production consistency for suitable sheet metal components.
This 1,200 mm panel application illustrates how a coordinated bending cell can support a one-operator workflow while reducing the recorded bending cycle time.
For More Details, Consult Your KLD Sheet Metal Solution Experts
We help you deliver the quality and value required for sheet metal processing equipment.
Consult Our Experts →